Clik here to view.
PAM3 voltage source
Is there any PAM3 voltage source in ADE/Spectre ? vsource from analogLib only supports NRZ and PAM4.
View ArticleClik here to view.
highlight net from Navigator
I would like to ask two questions (Version IC6.18 -64b.500.8). 1. In schematic L, when I click on a net on Navigator (like net7) how can I highlight it at the same time on schematic so I can see easily...
View ArticleClik here to view.
Is there any way to get the name of all components I use in schematic editor?
Is there any way to get the name of all components I use in schematic L (version IC6.18 -64b.500.8)? for example (nmos5v, nmos2v, rnhpoly, etc)
View ArticleClik here to view.
How to forbiden auto-starting a new line in netlisting
Hello, when i creat netlist, the script could start a new line automatically, which is annoying when i compare multiple netlist. Is there any way to forbidden such start a new line action? I can accept...
View ArticleClik here to view.
Cmin as as dynamic parameter change
Hi Team, I would like to know if I could dynamically ( in transient simulation) change cmin using dynamic parameter. When I looked into the parameter list in the drop down menu, I didn't...
View ArticleClik here to view.
What is best resource to learn Ocean scripting
Hi I am new to Ocean scripting. Could you help to tell me where I could find the resource (documentation with testcases, training, fast adoption kit) ?Thanks,ManChak
View ArticleClik here to view.
Run AMS simulation with ADE-L with import systemVerilogCustom_pkg::*
Hi Support, I am running ADE-L simulation with Config view. One block is with SystemVerilog and another one is pure analog circuit with transistors. In SystemVerilog, I need to import custom library...
View ArticleClik here to view.
Check output signals during simulation time
I'm trying to run a circuit in ADE L with transient analysis. Assume that my simulation time is 3m seconds. Sometimes I can check the output signals by Direct Plot --> Transient Signals after...
View ArticleClik here to view.
Add new output expression to an old run in Assembler
Assembler saves the results of all corner/sweep runs. I would like to take the results of a previous run, and define a new output parameter to be plotted. How can I do?What I've tried: Set the History...
View ArticleClik here to view.
Update wont pick up changes
Hello,In Virtuoso Layout GXL, when updating instances, nets, or ports in Virtuoso Layout XL (this is for layout generated all from source), the changes will not take effect in the layout GXL view. The...
View ArticleClik here to view.
using cross to find limits
I want to determine what input voltage makes a unity gain amplifier gain exceed the spec limits of +/- 2%. So I sweep the input voltage, calculate the gain and use the following functions:upper limit:...
View ArticleClik here to view.
How can perform AC analysis for switch capacitor circuit filter
Im working on a Low pass filter switched capacitor filter and Im using Cadence Virtuoso. I wolud like to know if it its possible to perform an AC Analysis
View ArticleClik here to view.
Failed to create netlist when simulating extracted view
Hello,In simulating extracted view, I get the following error:The question is where do I set simChecTermMismatchAction to ignore or warning?ERROR (OSSHNL-912): Netlisting failed because terminal...
View ArticleClik here to view.
Difference between mustJoinNet() and joinableNet() commands in Assura
I have two vss! pins at the top level of the chip which are supposed to be separate on the top level of the chip. But they both short to the P substrate of the chip. Eventually they will be shorted on...
View ArticleClik here to view.
Change properties of text
How can I change the properties of these text? I red comphelp file and tried to change the wire label for SUB as below but it doesn't work. I'd like to change it to another color and more bold.
View ArticleClik here to view.
Use of CCCSCreateWaveCSV.il for csv file having multiple coulmns (more than two)
Dear All,I am able to use CCSCreateWaveCSV.il for creating a wave from a .csv file having two columns (x-axis for 1st column, y-axis for 2nd column).But, is there a way we can use it for csv file...
View ArticleClik here to view.
How can I hide cell name of components in schematic?
How can I hide cell name of components in schematic?I know I can do that by changing its value in Edit Object Properties however it would take ages to do that manually for all components. If I change...
View ArticleClik here to view.
Is it possible to re-use generated DSPF when using Smartviews to reduce...
Hi! I really like the advantages of the new smartviews. However, simulation time increases since each time I run a point Spectre seems to generate a DSPF from scratch, and for large cells this can take...
View ArticleClik here to view.
ADE-L: how to add include file without using hard-coded paths
Hi! Is it possible to tell ADE-L to include a file without needing to hard-code its path? This procedure works in Assembler, but fails in ADE-L:1. I put the file to include (say "input.scs") under the...
View ArticleClik here to view.
Can you set the schematic annotations simulation results directory remotely...
I'm slowly getting back into design mode after many months in layout and seem to have forgotten a detail of a feature I put into my schematics to annotate device operating points and bias currents in...
View Article