Unable to copy data format of ADE results tab to LibreOffice Calc
Hi,I am trying to copy data directly from ADE results tab and paste it to LibreOffice calc instead of exporting to excel format, which is much more trivial.However, it seems to lose some format...
View ArticleAdding a new parameter to the cdf for each cell in a library
I need to add a new property to the CDF fro every cell in a library.The new property name is "model" and the value must be the same as the Cell Name.I am trying with...
View ArticleClik here to view.
Test-bench for hysteresis window of a StrongArm Latch comparator
Good afternoon! I've been trying to run a simulation for analysing the hysteresis of a given comparator, but with no success. I'm following De la Rosa's "CMOS Sigma-Delta Converters" book, where he...
View ArticleDoes Quantus Release Version 19.13 work with IC6.17?
I was wondering if Quantus Release Version 19.13 will work with IC6.17?If not which version.At the moment I get this message:ERROR (EXTQRCXLOG-108) : Exiting due to a error reported by the operating...
View ArticleAccess control of the cells in the library
Dear All,In my case, I have several different design libraries running in parallel. Those designs share some building blocks. In order to avoid messing up those designs, I would like to add some access...
View ArticleErrors when trying to complete QRC exraction
I'm using EXT19.13 following successful LVS.However I now get this error:INFO (LBRCXM-699): Errors exist in master control file "/tmp/qrc_45599/1/__qrc.rcx_cmd".ERROR (LBRCXM-709): ***** Quantus...
View ArticleADE L ERROR
Hellow, I try to run ADEL after i installed the new version of cadence and this error pops up "ERROR (ADE-5704): Variable 'options faultDoSampling' is either not declared or does not exist for analysis...
View ArticleAny Virtuoso based tool/script for placing small instances (just has two...
So I had a requirement for any Virtuoso based tool/script that can place small instances (just has two pins) automatically on level-1 pins, as I had quite a lot of such cases and placing all of them...
View ArticleAutostop in Maestro after evaluating all measurements
HiI have over 80 measuremnts inside Maestro. I want to stop given transient run after it has calculated all 80 measurements. As per my knowlege, Spectre autostop only on event condition. One of the way...
View ArticleBuilding string variables from string variables in ADE
I would like to run simulations with different waveform files for an ipwlf source. The waveform file is given to the component through a design variable, to make it easy to change. The waveform...
View ArticleSKILL calculator function: create a family plot of a different function with...
Hello,I would like to create a function which gets the following parameters:(func_name, parameters, parameter_name_to_sweep, start_value, step_size, stop_value)The function should call the func_name...
View ArticleClik here to view.
How to adjust width of "Corners" column (the 1st column) in Maestro Corner...
Hello,I am using Virtuoso Custom IC Design Environment version IC6.1.8-64b.500.27.In Corner Setup window the first column's width adjustment vertical line segment is grayed out (as can be seen in the...
View ArticlePlotting Expression Output Vs. Swept Design Variable
I'm running a corner simulation in Explorer/Assembler where a scalar output is calculated in an expression. I'd like to plot this scalar value against the swept design variable for the corresponding...
View ArticleClik here to view.
Export/save results data to csv in Explorer
Hello everyone,How do I save simulation results to a csv file in Explorer? My results only contains numbers as it's looking for ymax() of each signal.I only need the Name and Value columns to be saved....
View ArticleClik here to view.
Characters missing in Cadence Abstract Tool
Dear,In our server, some characters are missing in the "Abstract" GUI as follows:could you plz give me a support?Thanks.
View Articlediffstbprobe cause sim fail
Hi,I use diffstbprobe to check stablity of the loop. The sim got error info in the log as"The instance `Idiffprb' is referencing an undefined model or subcircuit, `diffstbprobe'. Either include the...
View ArticleHOW TO GET BACK LIBRARY SYMBOL
I accidently replace symbol of siltera library of component ls_otc_61m and get error. Im not changing it schematic, only the symbol. How can i restore the original symbol? Well, im dummies in IC design...
View ArticleMaestro to Adexl Import
Adexl to Maestro is one-click button by opening Adexl view with Assembler. But how to import Meastro data to Adexl? I can't find any save state or import from Adexl options. Please help.
View ArticleClik here to view.
Bulk Type Unavailable in Schematic L
I'm using IC614 environment with a TSMC65N PDK, and the body type (integrated/detached) isn't shown when making the schematic, why is that? do I have to install the PDK again or is there some sort of...
View ArticleSetup Script to Run Spectre from Command Line
HiIn the environment I'm currently working, I'm using a setup script as below to start the graphical version of Virtuoso.module load ic/618/06.18.290module load assura/41/618/04.16.111module load...
View Article