Hi All,
I'm encountering an error while generating the netlist in ADE/ADEXL for post-layout simulation of my design. I have used the spectre output (PEX Output) as input of few block of my interest in the config view. When I tried to generate the netlist to make sure good to go for simulation, But the netlist didn't generate and it throws an error. The Error in the CIW is given below.
INFO (SCH-1170): Extracting "mux_v2_w_predriver_final schematic"
INFO (SCH-1426): Schematic check completed with no errors.
INFO (SCH-1181): "tx_2021 mux_v2_w_predriver_final schematic" saved.
generate netlist...
Begin Incremental Netlisting Jun 9 15:18:32 2022
*Error* eval: unbound variable - simPrintInhConnAttributes
*Error* eval: unbound variable - simPrintInhConnAttributes
*Error* eval: unbound variable - simPrintInhConnAttributes
End netlisting Jun 9 15:18:32 2022
ERROR (OSSHNL-514): Netlist generation failed because of the errors reported above. The netlist might not have been generated at all, or the generated netlist could be corrupt. Fix the reported errors and regenerate the netlist.
...unsuccessful.
I tried to trace it back if there is some error in the PEX generated spectre output file. But it doesn't shows any error in CIW. The contect of the CIW window is given below.
WARNING (OSSHNL-143): Incremental netlisting is not possible since the global map file '/tmp/shubham/simulation/tb_tx_2021/tb_tx_top_v2_final/adexl/results/data/.tmpADEDir_shubham/tb_tx_2021:tb_tx_top_v2_final:1/tb_tx_2021_tb_tx_top_v2_final_config_spectre/netlist/ihnl/globalmap', could
not be opened in the read mode for IHNL version number comparison. Therefore
re-netlisting the entire design.
INFO (OSSHNL-386): HED 'sourcefile' support is enabled by default. Set variable
'hnlSourceFileDisabled to 't to disable sourcefile support.
INFO (OSSHNL-384): Valid sourcefile '/home/shubham/Shubham_PhD_AMPICLAB/prbs10_8Ch_w_mux_final.pex.netlist' on cell 'tx_2021/prbs10_8Ch_w_mux_final' in config 'tb_tx_2021/tb_tx_top_v2_final/config'. This cell will be treated
as a stop point.
INFO (OSSHNL-384): Valid sourcefile '/home/shubham/Shubham_PhD_AMPICLAB/cml_divider_final.pex.netlist' on cell 'tx_2021/cml_divider_final' in config 'tb_tx_2021/tb_tx_top_v2_final/config'. This cell will be treated
as a stop point.
INFO (OSSHNL-384): Valid sourcefile '/home/shubham/Shubham_PhD_AMPICLAB/8to4_mux.pex.netlist' on cell 'tx_2021/8to4_mux' in config 'tb_tx_2021/tb_tx_top_v2_final/config'. This cell will be treated
as a stop point.
INFO (OSSHNL-384): Valid sourcefile '/home/shubham/Shubham_PhD_AMPICLAB/clock_unit_final_seg_final.pex.netlist' on cell 'tx_2021/clock_unit_final_seg_final' in config 'tb_tx_2021/tb_tx_top_v2_final/config'. This cell will be treated
as a stop point.
INFO (OSSHNL-384): Valid sourcefile '/home/shubham/Shubham_PhD_AMPICLAB/bias_global.pex.netlist' on cell '25G_RING_TX/bias_global' in config 'tb_tx_2021/tb_tx_top_v2_final/config'. This cell will be treated
as a stop point.
*Error* eval: unbound variable - simPrintInhConnAttributes
*Error* eval: unbound variable - simPrintInhConnAttributes
*Error* eval: unbound variable - simPrintInhConnAttributes
End netlisting Jun 9 14:21:16 2022
ERROR (OSSHNL-514): Netlist generation failed because of the errors reported above. The netlist might not have been generated at all, or the generated netlist could be corrupt. Fix the reported errors and regenerate the netlist.
...unsuccessful.