Wrong Constraint Values in Sequential Cell Characterization

Hi,

I am trying to characterize a D flip-flop for low voltage operation (0.6V) using Cadence Liberate (V16). This is a positive edge triggered D flip flop based on true-single-phase clocking scheme. After the characterization, the measurements reported for hold constraint arcs seem to deviate significantly from its (spectre) spice simulation.

The constraint and the power settings to the liberate are as follows : 

# -------------------------------------------- Timing Constraints --------------------------------------------------------------------------------
### Input waveform ###
set_var predriver_waveform 2;# 2=use pre-driver waveform
### Capacitance ###
set_var min_capacitance_for_outputs 1;# write min_capacitance attribute for output pins
### Timing ###
set_var force_condition 4
### Constraint ###
set_var constraint_info 2
#set_var constraint_search_time_abstol 1e-12 ;# 1ps resolution for bisection search
set_var nochange_mode 1 ;# enable nochange_* constraint characterization
### min_pulse_width ###
set_var conditional_mpw 0
set_var constraint_combinational 2

#---------------------------------------------- CCS Settings ----------------------------------------------------------------------------------------
set_var ccsn_include_passgate_attr 1
set_var ccsn_model_related_node_attr 1
set_var write_library_is_unbuffered 1

set_var ccsp_min_pts 15 ;# CCSP accuracy
set_var ccsp_rel_tol 0.01 ;# CCSP accuracy
set_var ccsp_table_reduction 0 ;# CCSP accuracy
set_var ccsp_tail_tol 0.02 ;# CCSP accuracy
set_var ccsp_related_pin_mode 2 ;# use 3 for multiple input switching scnarios and Voltus only libraries

#----------------------------------------------- Power ---------------------------------------------------------------------------------------------------
### Leakage ###
set_var max_leakage_vector [expr 2**10]
set_var leakage_float_internal_supply 0 ;# get worst case leakage for power switch cells when off
set_var reset_negative_leakage_power 1 ;# convert negative leakage current to 0

### Power ###
set_var voltage_map 1 ;# create pg_pin groups, related_power_pin / related_ground_pin
set_var pin_based_power 0 ;# 0=based on VDD only; 1=power based on VDD and VSS (default);
set_var power_combinational_include_output 0 ;# do not include output pins in when conditions for combinational cells

set_var force_default_group 1
set_default_group -criteria {power avg} ;# use average for default power group

#set_var power_subtract_leakage 4 ;# use 4 for cells with exhaustive leakage states.
set_var subtract_hidden_power 2 ;# 1=subtract hidden power for all cells
set_var subtract_hidden_power_use_default 3 ;# 3=subtract hidden power from matched when condition then default group
set_var power_multi_output_binning_mode 1 ;# binning for multi-output cell considered for both timing and power arcs
set_var power_minimize_switching 1
set_var max_hidden_vector [expr 2**10]
#--------------------------------------------------------------------------------------------------------------------------------------------------------------

I specifically used set_var constraint_combinational 2 in the settings, in case the Bisection pass/fail mode fails to capture the constraints. In my spice simulation, the hold_rise (D=1, CLK=R, Q=R) arc at-least requires ~250 ps for minimum CLK/D slew combination (for the  by default smallest capacitive load as per Liberate)  while Liberate reports only ~30 ps. The define_cell template to this flip flop is pretty generic, which does not have any user specified arcs. So which settings most likely affecting the constraint measurements in Liberate and how can I debug this issue ?

Thanks

Anuradha

Image may be NSFW.
Clik here to view.

Image may be NSFW.
Clik here to view.